A-15PIN Installation
The A-15PIN is an A10-RX accessory allowing for direct connection with a range of Sony professional camcorders. The instructions below describe installation of the A10-RX in the A-15PIN and attaching the assembled A-15PIN to a Sony professional camcorder.
A-15PIN은 다양한 Sony 전문가용 캠코더와 직접 연결할 수 있도록 해주는 A10-RX 액세서리입니다. 아래 안내는 A10-RX를 A-15PIN에 설치하고, 조립된 A-15PIN을 Sony 전문가용 캠코더에 장착하는 방법을 설명합니다.
Supported Sony Cameras
PXW-Z750
PXW-Z450
PXW-Z400
PXW-X320
PMW-400
PDW-850
PXW-FX9 (Requires XDCA-FX9 Extension unit for FX9 camcorder)
지원 Sony 카메라
PXW-Z750
PXW-Z450
PXW-Z400
PXW-X320
PMW-400
PDW-850
PXW-FX9
FX9 캠코더의 경우 XDCA-FX9 확장 유닛 필요
Supplies Required
필요한 준비물
Step 1
Update the A10-RX firmware to v3.00. The A-15PIN does not support firmware prior to v3.00. Power down the A10-RX and remove all power.
A10-RX 펌웨어를 v3.00으로 업데이트합니다. A-15PIN은 v3.00 이전 펌웨어를 지원하지 않습니다. A10-RX의 전원을 끄고 모든 전원을 분리합니다.
Step 2
Detach the A-SL or A-XLR from the A10-RX by removing the four 16MM screws from the corners. Store the screws in a safe place for later use.
모서리에 있는 16mm 나사 4개를 제거하여 A-SL 또는 A-XLR을 A10-RX에서 분리합니다. 나중에 사용할 수 있도록 나사를 안전한 곳에 보관합니다.
Step 3
Slide the A10-RX into the A-15PIN slot so that the A10-RX and A-15PIN screw holes align. The A10-RX should be fully-seated against the A-15PIN top plate.
A10-RX와 A-15PIN의 나사 구멍이 맞도록 A10-RX를 A-15PIN 슬롯 안으로 밀어 넣습니다. A10-RX는 A-15PIN 상단 플레이트에 완전히 밀착되어야 합니다.
Step 4
Attach the A10-RX front panel to the A-15PIN using two of the provided screws and a Phillips head screwdriver.
제공된 나사 2개와 십자 드라이버를 사용해 A10-RX 전면 패널을 A-15PIN에 고정합니다.
Step 5
Attach the A10-RX rear panel to the A-15PIN using the remaining four provided screws and a Phillips head screwdriver.
남은 제공 나사 4개와 십자 드라이버를 사용해 A10-RX 후면 패널을 A-15PIN에 고정합니다.
Step 6
Insert the assembled A10-RX and A-15PIN into the rear mount slot of the Sony professional camcorder. The Sound Devices logo of the A-15PIN faces the rear of the camera. The A-15PIN pegs align with the Sony camcorder’s screw holes. Fully seat the A-15PIN against the camera.
조립된 A10-RX와 A-15PIN을 Sony 전문가용 캠코더의 후면 마운트 슬롯에 삽입합니다. A-15PIN의 Sound Devices 로고가 카메라 후면을 향하도록 합니다. A-15PIN의 페그가 Sony 캠코더의 나사 구멍과 맞아야 합니다. A-15PIN을 카메라에 완전히 밀착시킵니다.
Step 7
Attach the A-15PIN to the Sony camcorder using the four captive screws and a Phillips head screwdriver.
캡티브 나사 4개와 십자 드라이버를 사용해 A-15PIN을 Sony 캠코더에 고정합니다.