알림
뒤로
AiRAY Series
AiRAY Series
ViRAY Series
ViRAY Series
TiRAY Series
TiRAY Series

LINUS5-C : 

4 Channel DSP Amplifier with Loudspeaker Management

Integrated DSP, network and amplifier solution, High efficiency Class D amplifier engine
Main Features
  • Integrated DSP, network and amplifier solution
  • High efficiency Class D amplifier engine
  • Light weight SMPS power supply
  • SHARC floating point DSP @ 96 kHz
  • 4 balanced analogue inputs
  • LiNET-C: 4 x freely configurable digital audio signals over CAT5e
  • LINUS Control – network control and monitoring of amplifiers over Ethernet
  • CODA Audio factory presets using advanced linear phase FIR filters
  • 5 year warranty


System  Solutions


GENERAL

Number of output channels4
Output stageClass D
Internal samplerate / bit-depth96 kHz / 24 bit
Output-to-noise ratio
(22 Hz – 20 kHz, 4 Ω – analogue input)		>112 dB (unweighted)
>115 dB (A-weighted)
Signal-to-noice ratio
(22 Hz – 20 kHz, 4 Ω – digital input)		>114 dB (unweighted)
>117 dB (A-weighted)
Frequency response
(8 Ω load with CLEAR preset)		20 Hz – 20 kHz = (+0.5 dB /-1.0 dB)
THD+N
(4 Ω load @ 120 W output power)		20 Hz – 17 kHz = < 0.1%
Latency
(input to loudspeaker output)		Minimum 2.70 ms AES/EBU input
Minimum 2.00 ms analogue input
Protection circuitsInrush current limiter
Thermal limiter
Output DC
SMPS over-current
Output overload
LED indicatorsMute status
Limit
0 dB
Signal
Protection
Ethernet control active
Digital signal locked
Power on
Ethernet connection1 x 10 Mbps RJ45
AC mains input connectorNeutrik 32A powerCON®
AC mains input voltage**
(230 V internal jumper setting)		180 V = Minimum
230 V = Nominal
264 V = Maximum
AC mains input voltage**
(115 V internal jumper setting)		85 V = Minimum
115 V = Nominal
132 V = Maximum
AC mains frequency47 – 63 Hz
Power consumption*
(1/4 power = 150 W @ 4 Ω to represent typical music signal)		Amplifier in standby = 27 W
Amplifier idle = 115 W
Amplifier ¼ power = 851 W
Input sourcesAnalogue & AES/EBU
Analogue input impedance
(balanced)		30 kΩ
Maximum input level (analogue differential)+15 dBu / 4.36 Vrms
Input connections4x XLR3 Analogue IN
1x RJ45 Analogue IN (4x CH)
1x RJ45 Analogue LINK (4x CH)
1x RJ45 Digital IN (4x CH)
1x RJ45 Digital LINK (4x CH)
Supported digital input formats
(internal SRC)		32 kHz / 44.1 kHz / 48 kHz / 88.2 kHz / 96 kHz / 176.4 kHz / 192 kHz
RMS output power*
(20 Hz – 20 kHz, THD <0.1%)
(all channels driven)		400 W @ 8 Ω
700 W @ 4 Ω
900 W @ 2.7 Ω
1250 W @ 2 Ω
Peak output power*
(20 Hz – 20 kHz, 6 dB Crest Factor)
(all channels driven)		900 W pk @ 8 Ω
1600 W pk @ 4 Ω
1700 W pk @ 2.7 Ω
1600 W pk @ 2 Ω
Maximum output voltage*+/- 85 V pk
Maximum output current*+/- 38 A pk
Damping Factor
(8 Ω load, 1 kHz & below)		> 400
Minimum output load2 Ω nom
Power output connections2x Neutrik NL4 speakON®
1x Neutrik NL8 speakON®
Operating temperature+5°C to +55°C
41°F to 131°F
Thermal output
(BTU/h)		307.09 = Idle
665.37 = 20 %
1207.90 = 50 %
2108.70 = 100 %
Thermal output
(kWh)		0.090 = Idle
0.195 = 20 %
0.354 = 50 %
0.618 = 100 %
Cooling2x thermally controlled fans
Hot air expelled at rear
Dimensions (WxHxD)483.5 x 88 x 454.18 mm / 19.04” x 3.46” x 17.88” (2 Rack units)
Shipping Dim. (WxHxD)675 x 130 x 560 mm (0.049 m³) / 26.57” x 5.12” x 22.05”
Net Weight10.7 kg / 23.6 lbs
Shipping weight13.0 kg / 28.7 lbs
Volume = 0.049 m3 / 1.73 ft3

* Typical values – some variation may exist due to component tolerances.
**Voltage range should not be exceeded. Amplifier output power performance will degrade below nominal voltage & increase above nominal voltage.